IIVO - Connect PAR-FAR sensor on Modbus

IIVO - Connect PAR-FAR sensor on Modbus

  


    Update Q100 to latest firmware

    Inform the customer that critical processes (e.g. CHP, lighting) must be set to manual operation during the update.
    1. See Quick-Start IIVO on PartnerWiki for update Q100 head station: 
      https://hoogendoorn-partner-wiki.azurewebsites.net/en/start/io_update
    2. Download zip file from PartnerWiki
    3. Unzip zip file
    4. Sometimes there is an execution policy that prevents the selected file from executing. This can be changed by opening a command prompt window (CMD) as an administrator and running the following command: powershell -command "& {Set-ExecutionPolicy -ExecutionPolicy Unrestricted -Force}"
    5. Connect your laptop to the head station via 172.18.25.1, with subnet mask 255.255.0.0
    6. Start the Q100UpdateTool 
    7. Select for example Q100_Upgrade FWto22 SWto1.1.0.8 (Newest)

    Update IIVO to 5.15

    Inform the customer that critical processes (e.g. CHP, lighting) must be set to manual operation during the update.
    1. Server update.yagni.biz
    2. Click on Search for updates
    3. Click on Create update backup
    4. Click on Install update

    Add new terminal

    1. See this link for terminal position:
      https://hoogendoorn-partner-wiki.azurewebsites.net/en/product/721160
    2. Add terminal 750-652 - Modbus RTU converter 
    3. Change the properties 19200 baud, Even parity, 8 databits,  1 stopbit

    Connecting PAR-FAR sensor

    1. See IM on PartnerWiki
      https://hoogendoorn-partner-wiki.azurewebsites.net/en/product/650220
    2. Connect the PAR-FAR sensor

      If the device has also been added (see below) then:
      - LEDs A and E light up continuously
      - LED B and C flash (transmit/receive)

    Add device

    1. License must be adjusted (Max modbus device types)
    2. Add the device
      1. For example, use the IP address of the headstation 172.18.5.1. for 1st Data Connector
      2. Port for 1st modbus terminal 1502, and then continue numbering
    3. Set STATUS to ON
    4. Then Add node, address 1 (address 0 is broadcast)
      1. Then PAR, Far-red and heater status become available
    5. Connect PAR and Far-red to Custom simple/Custom measurement or PAR Crop Measurement 1 and Measurement 2
      PAR 0...4000 µmol/m²/s
      Far-red 0...1000 µmol/m²/s




      • Related Articles

      • IIVO - Aansluiten PAR-FAR sensor op Modbus - NL

        Q100 updaten naar nieuwste firmware Informeer de klant dat kritische processen (bijvoorbeeld WKK, belichting) handbediend gezet moeten worden tijdens de update. Zie Quick-Start IIVO op PartnerWiki voor update Q100 kopstation: ...

      • IIVO Sensor onderhoud

        PAR sensor 0-3000 umol Li-190R Een checkkit PAR wordt gebruikt om een PAR sensor te controleren en deze te vergelijken met een nieuwe sensor. Controleer of de ijkfactor correct is ingevuld in de IIVO: Meetbox droge en natte bol Meetbox boven doek ...

      • IIVO - Watchdog relais Finder 86

        Only 1 watchdog per IIVO control station Carefully read the installation manual on the PartnerWiki Check the DIP switches on the timer module Set the blue potentiometer for the time to approx. 35 sec. Click the watchdog relay on the DIN rail in the ...

      • IIVO - Set Weather Forecast & Radar Forecast

        Have the license adjusted if necessary Add software Give an understandable name Activate the maximum position radar forecast lee and wind side on the CONTROLS tab Add tab and panels for customer On correct dashboard e.g. Home Graph panel for Weather ...

      • EN - 025930 - How to use +PAR module?

        Question I have a PAR sensor in the greenhouse and the software module +PAR. How to use the +PAR module? Answer The iSii + PAR module is optional from version 3.3.3.1 or higher. With this module you can control the PAR value under the (partly) closed ...